Differences

This shows you the differences between two versions of the page.

--- sflow:dlinkswitch [2025/04/22 12:20] – santhana
+++ sflow:dlinkswitch [2025/04/22 13:37] (current) – santhana
@@ Line 3: / Line 3: @@
 =====Overview=====
-sFlow is a feature on D-Link switches that allows for monitoring network traffic by sampling packets and sending them to an sFlow analyzer for analysis. This document provides a brief guide on configuring sFlow on D-Link switches using the Command Line Interface (CLI).
+sFlow is a feature on D-Link switches that allows for monitoring network traffic by sampling packets and sending them to an sFlow analyzer for analysis. This document provides a brief guide on configuring sFlow on D-Link switches using the Command Line Interface (CLI). Make sure that the port numbers match the expected configuration where UDP port number is 6343 (default for sflow)
 =====Configuring sFlow=====
@@ Line 9: / Line 9: @@
 **Enable sFlow**: enable sflow
-**Create an sFlow analyzer server**: create sflow analyzer_server <id 1-4> owner <name 16> {timeout <sec 1-2000000> | collectoraddress <ipaddr> | collectorport <udp_port_number 1-65535> | maxdatagramsize <value 300-1400>}
+**Create an sFlow analyzer server**: create sflow analyzer_server <value 1-4> owner <name 16> {timeout <sec 1-2000000> | collectoraddress <ipaddr> | collectorPort <udp_port_number 1-65535> | maxdatagramsize <value 300-1400>}
-**Configure the sFlow analyzer server**: config sflow analyzer_server <id 1-4> {timeout <sec 1-2000000> | collectoraddress <ipaddr> | collectorport <udp_port_number 1-65535> | maxdatagramsize <value 300-1400>}
+**Configure the sFlow analyzer server**: config sflow analyzer_server <value 1-4> {timeout <sec 1-2000000> | collectoraddress <ipaddr> | collectorPort <udp_port_number 1-65535> | maxdatagramsize <value 300-1400>}
-**Create a counter poller**: create sflow counter_poller ports [<portlist> | all] analyzer_server_id <id 1-4> {interval [disable | <sec 20-120>]}
+**Create a counter poller**: create sflow counter_poller ports [<portlist> | all] analyzer_server_id <value 1-4> {interval [disable | <sec 20-120>]}
-**Create a flow sampler**: create sflow flow_sampler ports [<portlist> | all] analyzer_server_id <id 1-4> {rate <value 0-65535> | maxheadersize <value 18-256>}
+**Create a flow sampler**: create sflow flow_sampler ports [<portlist> | all] analyzer_server_id <value 1-4> {rate <value 0-65535> | maxheadersize <value 18-256>}
 =====Displaying sFlow Settings=====
@@ Line 32: / Line 32: @@
 </code>
-**Tips and Reminders**
+<note tip>**Tips and Reminders**
   * Make sure to configure the sFlow analyzer server with a valid IP address and UDP port number.
   * Configure the counter poller and flow sampler settings according to your network monitoring needs.
   * Use the show commands to verify your sFlow settings.
+</note>
-DLink sFlow Configuration Reference Doc: [[https://www.dlink.com/-/media/business_products/dgs/dgs-3627g/additional-downloads/dgs_3627g_cli_manual_fr.pdf|This Link points to source file]].
+**DLink sFlow Configuration Reference Doc**: [[https://www.dlink.com/-/media/business_products/dgs/dgs-3627g/additional-downloads/dgs_3627g_cli_manual_fr.pdf|This Link points to source file]].